Demo on VLAB
Goals
The goal of this demo is to show how to use VPCs, attach and peer them and run test connectivity between the servers. Examples are based on the default VLAB topology.
You can find instructions on how to setup VLAB in the Overview and Running VLAB sections.
Default topology
The default topology is Spine-Leaf with 2 spines, 2 MCLAG leaves, 2 ESLAG leaves and 1 non-MCLAG leaf. Optionally, you can choose to run
the default Collapsed Core topology using flag --fabric-mode collapsed-core (or -m collapsed-core) which only
consists of 2 switches.
For more details on customizing topologies see the Running VLAB section.
In the default topology, the following Control Node and Switch VMs are created, the Control Node is connected to every switch, the lines are ommitted for clarity:
graph TD
S1([Spine 1])
S2([Spine 2])
L1([MCLAG Leaf 1])
L2([MCLAG Leaf 2])
L3([ESLAG Leaf 3])
L4([ESLAG Leaf 4])
L5([Leaf 5])
L1 & L2 & L5 & L3 & L4 --> S1 & S2As well as the following test servers, as above Control Node connections are omitted:
graph TD
S1([Spine 1])
S2([Spine 2])
L1([MCLAG Leaf 1])
L2([MCLAG Leaf 2])
L3([ESLAG Leaf 3])
L4([ESLAG Leaf 4])
L5([Leaf 5])
TS1[Server 1]
TS2[Server 2]
TS3[Server 3]
TS4[Server 4]
TS5[Server 5]
TS6[Server 6]
TS7[Server 7]
TS8[Server 8]
TS9[Server 9]
TS10[Server 10]
subgraph MCLAG
L1
L2
end
TS3 --> L1
TS1 --> L1
TS1 --> L2
TS2 --> L1
TS2 --> L2
TS4 --> L2
subgraph ESLAG
L3
L4
end
TS7 --> L3
TS5 --> L3
TS5 --> L4
TS6 --> L3
TS6 --> L4
TS8 --> L4
TS9 --> L5
TS10 --> L5
L1 & L2 & L2 & L3 & L4 & L5 <----> S1 & S2Utility based VPC creation
Setup VPCs
hhfab vlab includes a utility to create VPCs in vlab. This utility is a hhfab vlab sub-command. hhfab vlab setup-vpcs.
NAME:
hhfab vlab setup-vpcs - setup VPCs and VPCAttachments for all servers and configure networking on them
USAGE:
hhfab vlab setup-vpcs [command options]
OPTIONS:
--dns-servers value, --dns value [ --dns-servers value, --dns value ] DNS servers for VPCs advertised by DHCP
--force-clenup, -f start with removing all existing VPCs and VPCAttachments (default: false)
--help, -h show help
--interface-mtu value, --mtu value interface MTU for VPCs advertised by DHCP (default: 0)
--ipns value IPv4 namespace for VPCs (default: "default")
--name value, -n value name of the VM or HW to access
--servers-per-subnet value, --servers value number of servers per subnet (default: 1)
--subnets-per-vpc value, --subnets value number of subnets per VPC (default: 1)
--time-servers value, --ntp value [ --time-servers value, --ntp value ] Time servers for VPCs advertised by DHCP
--vlanns value VLAN namespace for VPCs (default: "default")
--wait-switches-ready, --wait wait for switches to be ready before and after configuring VPCs and VPCAttachments (default: true)
Global options:
--brief, -b brief output (only warn and error) (default: false) [$HHFAB_BRIEF]
--cache-dir DIR use cache dir DIR for caching downloaded files (default: "/home/ubuntu/.hhfab-cache") [$HHFAB_CACHE_DIR]
--verbose, -v verbose output (includes debug) (default: false) [$HHFAB_VERBOSE]
--workdir PATH run as if hhfab was started in PATH instead of the current working directory (default: "/home/ubuntu") [$HHFAB_WORK_DIR]
Setup Peering
hhfab vlab includes a utility to create VPC peerings in VLAB. This utility is a hhfab vlab sub-command. hhfab vlab setup-peerings.
NAME:
hhfab vlab setup-peerings - setup VPC and External Peerings per requests (remove all if empty)
USAGE:
Setup test scenario with VPC/External Peerings by specifying requests in the format described below.
Example command:
$ hhfab vlab setup-peerings 1+2 2+4:r=border 1~as5835 2~as5835:subnets=sub1,sub2:prefixes=0.0.0.0/0,22.22.22.0/24
Which will produce:
1. VPC peering between vpc-01 and vpc-02
2. Remote VPC peering between vpc-02 and vpc-04 on switch group named border
3. External peering for vpc-01 with External as5835 with default vpc subnet and any routes from external permitted
4. External peering for vpc-02 with External as5835 with subnets sub1 and sub2 exposed from vpc-02 and default route
from external permitted as well any route that belongs to 22.22.22.0/24
VPC Peerings:
1+2 -- VPC peering between vpc-01 and vpc-02
demo-1+demo-2 -- VPC peering between demo-1 and demo-2
1+2:r -- remote VPC peering between vpc-01 and vpc-02 on switch group if only one switch group is present
1+2:r=border -- remote VPC peering between vpc-01 and vpc-02 on switch group named border
1+2:remote=border -- same as above
External Peerings:
1~as5835 -- external peering for vpc-01 with External as5835
1~ -- external peering for vpc-1 with external if only one external is present for ipv4 namespace of vpc-01, allowing
default subnet and any route from external
1~:subnets=default@prefixes=0.0.0.0/0 -- external peering for vpc-1 with auth external with default vpc subnet and
default route from external permitted
1~as5835:subnets=default,other:prefixes=0.0.0.0/0_le32_ge32,22.22.22.0/24 -- same but with more details
1~as5835:s=default,other:p=0.0.0.0/0_le32_ge32,22.22.22.0/24 -- same as above
OPTIONS:
--help, -h show help
--name value, -n value name of the VM or HW to access
--wait-switches-ready, --wait wait for switches to be ready before before and after configuring peerings (default: true)
Global options:
--brief, -b brief output (only warn and error) (default: false) [$HHFAB_BRIEF]
--cache-dir DIR use cache dir DIR for caching downloaded files (default: "/home/ubuntu/.hhfab-cache") [$HHFAB_CACHE_DIR]
--verbose, -v verbose output (includes debug) (default: false) [$HHFAB_VERBOSE]
--workdir PATH run as if hhfab was started in PATH instead of the current working directory (default: "/home/ubuntu") [$HHFAB_WORK_DIR]
Test Connectivity
hhfab vlab includes a utility to test connectivity between servers inside VLAB. This utility is a hhfab vlab sub-command. hhfab vlab test-connectivity.
NAME:
hhfab vlab test-connectivity - test connectivity between all servers
USAGE:
hhfab vlab test-connectivity [command options]
OPTIONS:
--curls value number of curl tests to run for each server to test external connectivity (0 to disable) (default: 3)
--help, -h show help
--iperfs value seconds of iperf3 test to run between each pair of reachable servers (0 to disable) (default: 10)
--iperfs-speed value minimum speed in Mbits/s for iperf3 test to consider successful (0 to not check speeds) (default: 7000)
--name value, -n value name of the VM or HW to access
--pings value number of pings to send between each pair of servers (0 to disable) (default: 5)
--wait-switches-ready, --wait wait for switches to be ready before testing connectivity (default: true)
Global options:
--brief, -b brief output (only warn and error) (default: false) [$HHFAB_BRIEF]
--cache-dir DIR use cache dir DIR for caching downloaded files (default: "/home/ubuntu/.hhfab-cache") [$HHFAB_CACHE_DIR]
--verbose, -v verbose output (includes debug) (default: false) [$HHFAB_VERBOSE]
--workdir PATH run as if hhfab was started in PATH instead of the current working directory (default: "/home/ubuntu") [$HHFAB_WORK_DIR]
Manual VPC creation
Creating and attaching VPCs
You can create and attach VPCs to the VMs using the kubectl fabric vpc command on the Control Node or outside of the
cluster using the kubeconfig. For example, run the following commands to create 2 VPCs with a single subnet each, a DHCP
server enabled with its optional IP address range start defined, and to attach them to some of the test servers:
core@control-1 ~ $ kubectl get conn | grep server
server-01--mclag--leaf-01--leaf-02 mclag 5h13m
server-02--mclag--leaf-01--leaf-02 mclag 5h13m
server-03--unbundled--leaf-01 unbundled 5h13m
server-04--bundled--leaf-02 bundled 5h13m
server-05--unbundled--leaf-03 unbundled 5h13m
server-06--bundled--leaf-03 bundled 5h13m
core@control-1 ~ $ kubectl fabric vpc create --name vpc-1 --subnet 10.0.1.0/24 --vlan 1001 --dhcp --dhcp-start 10.0.1.10
06:48:46 INF VPC created name=vpc-1
core@control-1 ~ $ kubectl fabric vpc create --name vpc-2 --subnet 10.0.2.0/24 --vlan 1002 --dhcp --dhcp-start 10.0.2.10
06:49:04 INF VPC created name=vpc-2
core@control-1 ~ $ kubectl fabric vpc attach --vpc-subnet vpc-1/default --connection server-01--mclag--leaf-01--leaf-02
06:49:24 INF VPCAttachment created name=vpc-1--default--server-01--mclag--leaf-01--leaf-02
core@control-1 ~ $ kubectl fabric vpc attach --vpc-subnet vpc-2/default --connection server-02--mclag--leaf-01--leaf-02
06:49:34 INF VPCAttachment created name=vpc-2--default--server-02--mclag--leaf-01--leaf-02
The VPC subnet should belong to an IPv4Namespace, the default one in the VLAB is 10.0.0.0/16:
After you created the VPCs and VPCAttachments, you can check the status of the agents to make sure that the requested configuration was applied to the switches:
core@control-1 ~ $ kubectl get agents
NAME ROLE DESCR APPLIED APPLIEDG CURRENTG VERSION
leaf-01 server-leaf VS-01 MCLAG 1 2m2s 5 5 v0.23.0
leaf-02 server-leaf VS-02 MCLAG 1 2m2s 4 4 v0.23.0
leaf-03 server-leaf VS-03 112s 5 5 v0.23.0
spine-01 spine VS-04 16m 3 3 v0.23.0
spine-02 spine VS-05 18m 4 4 v0.23.0
In this example, the values in columns APPLIEDG and CURRENTG are equal which means that the requested configuration
has been applied.
Setting up networking on test servers
You can use hhfab vlab ssh on the host to SSH into the test servers and configure networking there. For example, for
both server-01 (MCLAG attached to both leaf-01 and leaf-02) we need to configure a bond with a VLAN on top of it
and for the server-05 (single-homed unbundled attached to leaf-03) we need to configure just a VLAN and they both
will get an IP address from the DHCP server. You can use the ip command to configure networking on the servers or use
the little helper pre-installed by Fabricator on test servers, hhnet.
For server-01:
core@server-01 ~ $ hhnet cleanup
core@server-01 ~ $ hhnet bond 1001 enp2s1 enp2s2
10.0.1.10/24
core@server-01 ~ $ ip a
...
3: enp2s1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 state UP group default qlen 1000
link/ether 06:5a:e8:38:3b:ea brd ff:ff:ff:ff:ff:ff permaddr 0c:20:12:fe:01:01
4: enp2s2: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 state UP group default qlen 1000
link/ether 06:5a:e8:38:3b:ea brd ff:ff:ff:ff:ff:ff permaddr 0c:20:12:fe:01:02
6: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 06:5a:e8:38:3b:ea brd ff:ff:ff:ff:ff:ff
inet6 fe80::45a:e8ff:fe38:3bea/64 scope link
valid_lft forever preferred_lft forever
7: bond0.1001@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 06:5a:e8:38:3b:ea brd ff:ff:ff:ff:ff:ff
inet 10.0.1.10/24 metric 1024 brd 10.0.1.255 scope global dynamic bond0.1001
valid_lft 86396sec preferred_lft 86396sec
inet6 fe80::45a:e8ff:fe38:3bea/64 scope link
valid_lft forever preferred_lft forever
And for server-02:
core@server-02 ~ $ hhnet cleanup
core@server-02 ~ $ hhnet bond 1002 enp2s1 enp2s2
10.0.2.10/24
core@server-02 ~ $ ip a
...
3: enp2s1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 state UP group default qlen 1000
link/ether 5e:10:b1:f7:d0:4c brd ff:ff:ff:ff:ff:ff permaddr 0c:20:12:fe:02:01
4: enp2s2: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 state UP group default qlen 1000
link/ether 5e:10:b1:f7:d0:4c brd ff:ff:ff:ff:ff:ff permaddr 0c:20:12:fe:02:02
8: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 5e:10:b1:f7:d0:4c brd ff:ff:ff:ff:ff:ff
inet6 fe80::5c10:b1ff:fef7:d04c/64 scope link
valid_lft forever preferred_lft forever
9: bond0.1002@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 5e:10:b1:f7:d0:4c brd ff:ff:ff:ff:ff:ff
inet 10.0.2.10/24 metric 1024 brd 10.0.2.255 scope global dynamic bond0.1002
valid_lft 86185sec preferred_lft 86185sec
inet6 fe80::5c10:b1ff:fef7:d04c/64 scope link
valid_lft forever preferred_lft forever
Testing connectivity before peering
You can test connectivity between the servers before peering the switches using the ping command:
core@server-01 ~ $ ping 10.0.2.10
PING 10.0.2.10 (10.0.2.10) 56(84) bytes of data.
From 10.0.1.1 icmp_seq=1 Destination Net Unreachable
From 10.0.1.1 icmp_seq=2 Destination Net Unreachable
From 10.0.1.1 icmp_seq=3 Destination Net Unreachable
^C
--- 10.0.2.10 ping statistics ---
3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2003ms
core@server-02 ~ $ ping 10.0.1.10
PING 10.0.1.10 (10.0.1.10) 56(84) bytes of data.
From 10.0.2.1 icmp_seq=1 Destination Net Unreachable
From 10.0.2.1 icmp_seq=2 Destination Net Unreachable
From 10.0.2.1 icmp_seq=3 Destination Net Unreachable
^C
--- 10.0.1.10 ping statistics ---
3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2004ms
Peering VPCs and testing connectivity
To enable connectivity between the VPCs, peer them using kubectl fabric vpc peer:
core@control-1 ~ $ kubectl fabric vpc peer --vpc vpc-1 --vpc vpc-2
07:04:58 INF VPCPeering created name=vpc-1--vpc-2
Make sure to wait until the peering is applied to the switches using kubectl get agents command. After that, you can
test connectivity between the servers again:
core@server-01 ~ $ ping 10.0.2.10
PING 10.0.2.10 (10.0.2.10) 56(84) bytes of data.
64 bytes from 10.0.2.10: icmp_seq=1 ttl=62 time=6.25 ms
64 bytes from 10.0.2.10: icmp_seq=2 ttl=62 time=7.60 ms
64 bytes from 10.0.2.10: icmp_seq=3 ttl=62 time=8.60 ms
^C
--- 10.0.2.10 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2004ms
rtt min/avg/max/mdev = 6.245/7.481/8.601/0.965 ms
core@server-02 ~ $ ping 10.0.1.10
PING 10.0.1.10 (10.0.1.10) 56(84) bytes of data.
64 bytes from 10.0.1.10: icmp_seq=1 ttl=62 time=5.44 ms
64 bytes from 10.0.1.10: icmp_seq=2 ttl=62 time=6.66 ms
64 bytes from 10.0.1.10: icmp_seq=3 ttl=62 time=4.49 ms
^C
--- 10.0.1.10 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2004ms
rtt min/avg/max/mdev = 4.489/5.529/6.656/0.886 ms
If you delete the VPC peering with kubectl delete applied to the relevant object and wait for the agent to apply the
configuration on the switches, you can observe that connectivity is lost again:
core@control-1 ~ $ kubectl delete vpcpeering/vpc-1--vpc-2
vpcpeering.vpc.githedgehog.com "vpc-1--vpc-2" deleted
core@server-01 ~ $ ping 10.0.2.10
PING 10.0.2.10 (10.0.2.10) 56(84) bytes of data.
From 10.0.1.1 icmp_seq=1 Destination Net Unreachable
From 10.0.1.1 icmp_seq=2 Destination Net Unreachable
From 10.0.1.1 icmp_seq=3 Destination Net Unreachable
^C
--- 10.0.2.10 ping statistics ---
3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2004ms
You can see duplicate packets in the output of the ping command between some of the servers. This is expected
behavior and is caused by the limitations in the VLAB environment.
core@server-01 ~ $ ping 10.0.5.10
PING 10.0.5.10 (10.0.5.10) 56(84) bytes of data.
64 bytes from 10.0.5.10: icmp_seq=1 ttl=62 time=9.58 ms
64 bytes from 10.0.5.10: icmp_seq=1 ttl=62 time=9.58 ms (DUP!)
64 bytes from 10.0.5.10: icmp_seq=2 ttl=62 time=6.99 ms
64 bytes from 10.0.5.10: icmp_seq=2 ttl=62 time=6.99 ms (DUP!)
64 bytes from 10.0.5.10: icmp_seq=3 ttl=62 time=9.59 ms
64 bytes from 10.0.5.10: icmp_seq=3 ttl=62 time=9.60 ms (DUP!)
^C
--- 10.0.5.10 ping statistics ---
3 packets transmitted, 3 received, +3 duplicates, 0% packet loss, time 2003ms
rtt min/avg/max/mdev = 6.987/8.720/9.595/1.226 ms
Using VPCs with overlapping subnets
First, create a second IPv4Namespace with the same subnet as the default one:
core@control-1 ~ $ kubectl get ipns
NAME SUBNETS AGE
default ["10.0.0.0/16"] 24m
core@control-1 ~ $ cat <<EOF > ipns-2.yaml
apiVersion: vpc.githedgehog.com/v1beta1
kind: IPv4Namespace
metadata:
name: ipns-2
namespace: default
spec:
subnets:
- 10.0.0.0/16
EOF
core@control-1 ~ $ kubectl apply -f ipns-2.yaml
ipv4namespace.vpc.githedgehog.com/ipns-2 created
core@control-1 ~ $ kubectl get ipns
NAME SUBNETS AGE
default ["10.0.0.0/16"] 30m
ipns-2 ["10.0.0.0/16"] 8s
Let's assume that vpc-1 already exists and is attached to server-01 (see Creating and attaching VPCs).
Now we can create vpc-3 with the same subnet as vpc-1 (but in the different IPv4Namespace) and attach it to the
server-03:
core@control-1 ~ $ cat <<EOF > vpc-3.yaml
apiVersion: vpc.githedgehog.com/v1beta1
kind: VPC
metadata:
name: vpc-3
namespace: default
spec:
ipv4Namespace: ipns-2
subnets:
default:
dhcp:
enable: true
range:
start: 10.0.1.10
subnet: 10.0.1.0/24
vlan: 2001
vlanNamespace: default
EOF
core@control-1 ~ $ kubectl apply -f vpc-3.yaml
At that point you can setup networking on server-03 the same as you did for server-01 and server-02 in
a previous section. Once you have configured networking, server-01 and
server-03 have IP addresses from the same subnets.